Registered: Mar 2003
Location: Bayonne, New Jersey
Posts: 52

I have a Series 1 Tivo (Sony SVR-2000) and have just installed a Turbonet card an hour ago. The only thing I want to do (for now) is do the daily call via ethernet over my home network. It is a no-go.

I have put in the prefix, and when I try to test the connection, it says (Failed. Couldn't connect).

Is there something that I am not doing that needs to be done? I was under the impression that, for only installing the Turbonet card, and wanting to get the daily call, there was nothing else that I would have to do, besides putting in the prefix.

I have restarted the network, and reset the Tivo. Checked all connections. Green light is on the card. Green light blinks every 10-15 seconds.

Do I have to plug the Tivo in a regular phone jack once more, and reset the calling data?

I tried System reset... to no avail.

Does the Linksys router have to have any special settings to allow this?

Any suggestions? It's probably something stupid I'm forgetting...

Brian










POST #1 | Report this post to a moderator | IP: Logged

POST #1 | Report this post to a moderator | IP: Logged

Registered: May 2001
Location: Los Angeles
Posts: 3155

You do need DHCP active on the router - and also you should check the DHCP table in the router to see if the TiVo sought, and was given, an address.

Have you tried a laptop with DHCP from the same jack to see if it could see the internet?

Michael

__________________
WeaKnees - Proud TiVo Community Special Sponsor

POST #2 | Report this post to a moderator | IP: Logged

Registered: Apr 2002
Location:
Posts: 295

2 things I would check,

1 - make sure the connections are on BEFORE powering up TiVo. DHCP request only comes during the boot process, so if tivo did not get an IP during boot up, it will not get one untill next reboot.

2 - make sure TiVo software is 3.x+ . If not, you MUST run the install script for turbonet. Only in 3.0 they added support for the TurboNet and dial out string out of the box.

-H

POST #3 | Report this post to a moderator | IP: Logged

Registered: Mar 2003
Location: Bayonne, New Jersey
Posts: 52

weaknees- Laptop works from same connection. DHCP is active on the router and computer. Both my Mac using Optimum Online, and my phone service, Vonage, immediately grab an IP, which is viewable from the Linksys page. No matter how many times I reboot, the Tivo still doesn't get it's own IP.

Hichhiker- Connections were all active before I powered up the TIVO, I even waited longer because I read somewhere that the TurboNET card will not work properly if you don't wait a while after you turn off your Tivo, to turn it back on.
Running 3.0+ software. When I bring up the routing table on the Linksys page, the two IP's, and their respective MAC addresses come up. One for the computer, and the second is for the Vonage.

I've done many things with computers and home networks. For all intents and purposes, this is supposed to... just... WORK!!! I don't understand why the TurboNET card just doesn't grab an IP. Could it be the card from 9th tee itself???

POST #4 | Report this post to a moderator | IP: Logged

Registered: Jan 2003
Location: Wilmington, NC
Posts: 77

Did you also reboot the router, and then the Tivo? I found I had to do that to get it to work.

POST #5 | Report this post to a moderator | IP: Logged

Registered: Jan 2002
Location:
Posts: 2223

Hi,

Double check the dialing prefix - <comma><hash><four><zero><one>

THe next step will be to check the logs.

The easiest way to do that is to burn the nic_install CD (www.silicondust.com) and use nic_install on a PC with the tivo drive attached to dump the log file.

Nick

__________________
Silicondust - Tivo CacheCARD/Turbonet/Airnet
Roomba Robotics - Roomba Community

POST #6 | Report this post to a moderator | IP: Logged

Registered: Mar 2003
Location: Bayonne, New Jersey
Posts: 52

Hello,

The prefix is correct. I don't have access to a PC... all Macs at work (Local High School), and I have 1 Mac at home. Can I check the logs any other way?

POST #7 | Report this post to a moderator | IP: Logged

Registered: Oct 2002
Location:
Posts: 43

Yes, if you have 3.0. Enable backdoors, play any recorded program, then enter CLEAR-ENTER-CLEAR-ThumbsUp on your remote. Then use PageUp/PageDown and the arrows on the remote to navigate the logs.

More details on enabling backdoors, and on using the CLEAR-ENTER-CLEAR codes, can be found here:

http://www.tivocommunity.com/tivo-v...5706#post205706

POST #8 | Report this post to a moderator | IP: Logged

Registered: Mar 2003
Location: Bayonne, New Jersey
Posts: 52

Ok, give me a few hours, and I'll report on what I find when I go home and try this. Thank you everyone for being so patient while I find out why something such as this, which should work so easily, doesn't.

POST #9 | Report this post to a moderator | IP: Logged

Registered: Oct 2002
Location:
Posts: 43

Call me crazy, but I think it may be a problem with the router. I had something similar to this happen to me once. Maybe you could try refreshing the DHCP clients table?

POST #10 | Report this post to a moderator | IP: Logged

Registered: Mar 2003
Location: Bayonne, New Jersey
Posts: 52

Refreshing the DHCP has no effect.
OK - in the log, under "messages", it has a heading of
**NETWORK DEVICE INFO** in a nutshell:
pppd 2.4.1 started by TiVo, uid 0
Couldn't restrict write permission to /dev/cua1:Read only file system
Using interface ppp0
Connect ppp0 <->/dev/cua1
local IP address 192.168.XX.XX
remote IP address 204.176.XX.XX
Terminating on signal 15
Connection Terminated
Connect time 0.8 minutes
Sent 66619 bytes, received 3760 bytes
tcflush failed: invalid arguement
Exit


If I should be looking in another log, please let me know...
BTW- The Local IP address is what I should be seeing on the Linksys routing table page, correct? Is there a way to manually "force" the IP number in regards to the router?

Last edited by mahermusic on 03-14-2003 at 02:33 AM

POST #11 | Report this post to a moderator | IP: Logged

Registered: Mar 2003
Location: Bayonne, New Jersey
Posts: 52

Here's another log, and it's info (in a nutshell)

/var/log/tclient

CallService: Start err 0
CAM_ID not found
CallStatusReporter: Phase: Dial, Status In Progress
CallStatusReporter: sending message "CL/30"
Backdoor code 4, enable calls via Broadband
CallStatusReporter: Turning off-hook LED on
Opening Device
Initializing Modem
ATZ
OK
Determining Modem Type
ATI3
V2.210K1-V34_DLP
OK
Modem is OLD
Set up modem and check for availability
Setting up old modem
0007: BB
02
0008: EO
OK
ATQO
OK
ATSO=O
OK
ATW2S6=8S7=50S11=100%CO&D2+MS=11,1,300,33600,0,0
OK
Modem set up and onhook
Turning off dial tone detection
ATX3
OK Trying to connect
ATDT18778771756
CONNECT 28800
Got a connection
Trying to login
TIVO MAX TNT
Login:
(lots of numbers)@tivo.net
Password:
Entering PPP session
IP address is 192
Login is complete
Modem dialcode is 1
CallStatusReporter: Phase: Dial, Status In Progress
CallStatusReporter: sending message "CL/31"


(says other things, and then...)

CommUtil: connection to host 204.176.XX.XX.X p
err 0x0
Uploading HTTP Header for modlog of var/log/.....

then

SvcLogRqst: verify: unlink/var/log/svcupload (status=0)
couldn't stat input file, reason= No such file or directory
NetAgent::doXferpen failed on Rqst : No such file or directory
drainGetPostQ: doxfer failed err=65535 (Oxfill)

Any suggestions??? (WHEW...)

POST #12 | Report this post to a moderator | IP: Logged

Registered: Oct 2002
Location:
Posts: 43

quote:

---

Originally posted by mahermusic
Is there a way to manually "force" the IP number in regards to the router?

---

POST #13 | Report this post to a moderator | IP: Logged

Registered: Mar 2003
Location: Bayonne, New Jersey
Posts: 52

I THINK ITS BEEN FIXED...

I powered down the Tivo, opened it, took the TurboNET card out, then Powered up the Tivo without the card. Then, I powered down, put the card back in, and powered it up, and the Linksys router page now "sees" the card, and gave it an IP, and when I tried the daily call, it WORKED!!!

I've been rebooting the unit, but I guess it had to be rebooted once more WITHOUT the card, before it could play nicely WITH the card.

I'm happy!

Brian

POST #14 | Report this post to a moderator | IP: Logged